Diesel Version 5:CV 27 - Revision history

Tcsdcc: /* NMRA CV 27 (Decoder Automatic Stopping Configuration) */

2018-09-19T20:25:58Z

NMRA CV 27 (Decoder Automatic Stopping Configuration)

← Older revision		Revision as of 20:25, 19 September 2018
Line 1:		Line 1:
	== NMRA CV 27 (Decoder Automatic Stopping Configuration) ==		== NMRA CV 27 - Decoder Automatic Stopping Configuration ==
	Used to configure which actions will cause the decoder to automatically stop.		Used to configure which actions will cause the decoder to automatically stop.
	Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the		Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the

Shalee: /* NMRA CV 27 (Decoder Automatic Stopping Configuration) */

2018-06-25T16:11:50Z

NMRA CV 27 (Decoder Automatic Stopping Configuration)

← Older revision		Revision as of 16:11, 25 June 2018
Line 3:		Line 3:
	Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the		Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the
	right rail.		right rail.
	“0” = Disabled “1” = Enabled.		“0” = Disabled “1” = Enabled
	Bit 1 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail.		Bit 1 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail.
	“0” = Disabled “1” = Enabled		“0” = Disabled “1” = Enabled
Line 11:		Line 11:
	Bit 4 = Enable/Disable Auto Stop in the presence of reverse polarity DC		Bit 4 = Enable/Disable Auto Stop in the presence of reverse polarity DC
	“0” = Disabled “1” = Enabled		“0” = Disabled “1” = Enabled
	Bit 5 = Enable/Disable Auto Stop in		Bit 5 = Enable/Disable Auto Stop in the presence forward polarity DC.
	the presence forward polarity DC.
	“0” = Disabled “1” = Enabled		“0” = Disabled “1” = Enabled
	Bits 6-7 = Reserved for future use.		Bits 6-7 = Reserved for future use.

Shalee: Created page with "== NMRA CV 27 (Decoder Automatic Stopping Configuration) == Used to configure which actions will cause the decoder to automatically stop. Bit 0 = Enable/Disable Auto Stop in..."

2018-06-25T16:10:44Z

Created page with "== NMRA CV 27 (Decoder Automatic Stopping Configuration) == Used to configure which actions will cause the decoder to automatically stop. Bit 0 = Enable/Disable Auto Stop in..."

New page

== NMRA CV 27 (Decoder Automatic Stopping Configuration) ==
Used to configure which actions will cause the decoder to automatically stop.
Bit 0 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the
right rail.
“0” = Disabled “1” = Enabled.
Bit 1 = Enable/Disable Auto Stop in the presence of an asymmetrical DCC signal which is more positive on the left rail.
“0” = Disabled “1” = Enabled
Bit 2 = Enable/Disable Auto Stop in the presence of an Signal Controlled Influence cutout signal.
“0” = Disabled “1” = Enabled
Bit 3 = Reserved for Future Use
Bit 4 = Enable/Disable Auto Stop in the presence of reverse polarity DC
“0” = Disabled “1” = Enabled
Bit 5 = Enable/Disable Auto Stop in
the presence forward polarity DC.
“0” = Disabled “1” = Enabled
Bits 6-7 = Reserved for future use.
*Note If the decoder does not support a feature contained in this table, it shall not allow the corresponding bit to be
set improperly (i.e. the bit should always contain it’s default value).

{{Infobox
|title = NMRA 27
|header1 = Decoder Automatic Stopping Configuration
|label2 = Range of Values
|data2 = RANGE OF VALUES HERE
|label3 = Default Value
|data3 = DEFAULT VALUE
}}